-- These MIBs were created on 1/2/2003
-- This module defines enterprise MIBs for NS BGP
--
-- Copyright (c) 1999-2004, Juniper Networks, Inc.
-- All rights reserved.NETSCREEN-VR-BGP4-MIB DEFINITIONS::=BEGINIMPORTS
MODULE-IDENTITY,OBJECT-TYPE,NOTIFICATION-TYPE,IpAddress,Integer32,Counter32,Gauge32FROM SNMPv2-SMI
netscreenTrapDesc, netscreenTrapType
FROM NETSCREEN-TRAP-MIB
netscreenVR
FROM NETSCREEN-SMI;nsVrBgp MODULE-IDENTITYLAST-UPDATED"200506202022Z"-- June 20, 2005ORGANIZATION"Juniper Networks, Inc."CONTACT-INFO"Customer Support
1194 North Mathilda Avenue
Sunnyvale, California 94089-1206
USA
Tel: 1-800-638-8296
E-mail: customerservice@juniper.net
HTTP://www.juniper.net"DESCRIPTION"The MIB module for NS-BGP-4."::={ netscreenVR 6}-- BGP Info table. This table contains, one entry per-- VR, information about the BGP's Version, LocalAs and Identifier.nsVrBgpInfoTable OBJECT-TYPESYNTAXSEQUENCEOF NsVrBgpInfoEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"BGP info table. This table contains,
one entry per VR, information about
the BGP's Version, LocalAs and Identifier."::={ nsVrBgp 1}nsVrBgpInfoEntry OBJECT-TYPESYNTAX NsVrBgpInfoEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"Entry containing information about the
BGP's Version, LocalAs and Identifier"INDEX{ nsVrBgpInfoVRID }::={ nsVrBgpInfoTable 1}
NsVrBgpInfoEntry ::=SEQUENCE{
nsVrBgpInfoVersion
OCTETSTRING,
nsVrBgpInfoLocalAs
INTEGER,
nsVrBgpInfoIdentifier
IpAddress,
nsVrBgpInfoVRID
INTEGER}nsVrBgpInfoVersion OBJECT-TYPESYNTAXOCTETSTRING(SIZE(1..255))
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vector of supported BGP protocol version
numbers. Each peer negotiates the version
from this vector. Versions are identified
via the string of bits contained within this
object. The first octet contains bits 0 to
7, the second octet contains bits 8 to 15,
and so on, with the most significant bit
referring to the lowest bit number in the
octet (e.g., the MSB of the first octet
refers to bit 0). If a bit, i, is present
and set, then the version (i+1) of the BGP
is supported."::={ nsVrBgpInfoEntry 1}nsVrBgpInfoLocalAs OBJECT-TYPESYNTAXINTEGER(0..65535)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local autonomous system number."::={ nsVrBgpInfoEntry 2}nsVrBgpInfoIdentifier OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The BGP Identifier of local system."::={ nsVrBgpInfoEntry 3}nsVrBgpInfoVRID OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"Virtual Router ID. VRID range for system created
VRs: [1-1024] and for user created VRs: [1025-2048]"::={ nsVrBgpInfoEntry 4}-- BGP Peer table. This table contains, one entry per-- BGP peer, information about the BGP peer.nsVrBgpPeerTable OBJECT-TYPESYNTAXSEQUENCEOF NsVrBgpPeerEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"BGP peer table. This table contains,
one entry per BGP peer, information about
the connections with BGP peers."::={ nsVrBgp 3}nsVrBgpPeerEntry OBJECT-TYPESYNTAX NsVrBgpPeerEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Entry containing information about the
connection with a BGP peer."INDEX{ nsVrBgpPeerVRID,
nsVrBgpPeerRemoteAddr }::={ nsVrBgpPeerTable 1}
NsVrBgpPeerEntry ::=SEQUENCE{
nsVrBgpPeerIdentifier
IpAddress,
nsVrBgpPeerState
INTEGER,
nsVrBgpPeerAdminStatus
INTEGER,
nsVrBgpPeerNegotiatedVersion
Integer32,
nsVrBgpPeerLocalAddr
IpAddress,
nsVrBgpPeerLocalPort
INTEGER,
nsVrBgpPeerRemoteAddr
IpAddress,
nsVrBgpPeerRemotePort
INTEGER,
nsVrBgpPeerRemoteAs
INTEGER,
nsVrBgpPeerInUpdates
Counter32,
nsVrBgpPeerOutUpdates
Counter32,
nsVrBgpPeerInTotalMessages
Counter32,
nsVrBgpPeerOutTotalMessages
Counter32,
nsVrBgpPeerLastError
OCTETSTRING,
nsVrBgpPeerFsmEstablishedTransitions
Counter32,
nsVrBgpPeerFsmEstablishedTime
Gauge32,
nsVrBgpPeerConnectRetryInterval
INTEGER,
nsVrBgpPeerHoldTime
INTEGER,
nsVrBgpPeerKeepAlive
INTEGER,
nsVrBgpPeerHoldTimeConfigured
INTEGER,
nsVrBgpPeerKeepAliveConfigured
INTEGER,
nsVrBgpPeerMinASOriginationInterval
INTEGER,
nsVrBgpPeerMinRouteAdvertisementInterval
INTEGER,
nsVrBgpPeerInUpdateElapsedTime
Gauge32,
nsVrBgpPeerVRID
INTEGER}nsVrBgpPeerIdentifier OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"The BGP Identifier of this entry's BGP
peer."::={ nsVrBgpPeerEntry 1}nsVrBgpPeerState OBJECT-TYPESYNTAXINTEGER{idle(1),connect(2),active(3),opensent(4),openconfirm(5),established(6)}MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The BGP peer connection state."::={ nsVrBgpPeerEntry 2}nsVrBgpPeerAdminStatus OBJECT-TYPESYNTAXINTEGER{stop(1),start(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The desired state of the BGP connection.
A transition from 'stop' to 'start' will
cause the BGP Start Event to be generated.
A transition from 'start' to 'stop' will
cause the BGP Stop Event to be generated.
This parameter can be used to restart BGP
peer connections. Care should be used in
providing write access to this object
without adequate authentication."::={ nsVrBgpPeerEntry 3}nsVrBgpPeerNegotiatedVersion OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The negotiated version of BGP running
between the two peers."::={ nsVrBgpPeerEntry 4}nsVrBgpPeerLocalAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local IP address of this entry's BGP
connection."::={ nsVrBgpPeerEntry 5}
nsVrBgpPeerLocalPort OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The local port for the TCP connection
between the BGP peers."::={ nsVrBgpPeerEntry 6}nsVrBgpPeerRemoteAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The remote IP address of this entry's BGP
peer."::={ nsVrBgpPeerEntry 7}
nsVrBgpPeerRemotePort OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The remote port for the TCP connection
between the BGP peers. Note that the
objects nsVrBgpPeerLocalAddr,
nsVrBgpPeerLocalPort, nsVrBgpPeerRemoteAddr and
nsVrBgpPeerRemotePort provide the appropriate
reference to the standard MIB TCP
connection table."::={ nsVrBgpPeerEntry 8}nsVrBgpPeerRemoteAs OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The remote autonomous system number."::={ nsVrBgpPeerEntry 9}nsVrBgpPeerInUpdates OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The number of BGP UPDATE messages
received on this connection. This object
should be initialized to zero (0) when the
connection is established."::={ nsVrBgpPeerEntry 10}nsVrBgpPeerOutUpdates OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrent
DESCRIPTION"The number of BGP UPDATE messages
transmitted on this connection. This
object should be initialized to zero (0)
when the connection is established."::={ nsVrBgpPeerEntry 11}nsVrBgpPeerInTotalMessages OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of messages received
from the remote peer on this connection.
This object should be initialized to zero
when the connection is established."::={ nsVrBgpPeerEntry 12}nsVrBgpPeerOutTotalMessages OBJECT-TYPESYNTAXCounter32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of messages transmitted to
the remote peer on this connection. This
object should be initialized to zero when
the connection is established."::={ nsVrBgpPeerEntry 13}nsVrBgpPeerLastError OBJECT-TYPESYNTAXOCTETSTRING(SIZE(2))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The last error code and subcode seen by this
peer on this connection. If no error has
occurred, this field is zero. Otherwise, the
first byte of this two byte OCTET STRING
contains the error code, and the second byte
contains the subcode."::={ nsVrBgpPeerEntry 14}nsVrBgpPeerFsmEstablishedTransitions OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The total number of times the BGP FSM
transitioned into the established state."::={ nsVrBgpPeerEntry 15}nsVrBgpPeerFsmEstablishedTime OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This timer indicates how long (in
seconds) this peer has been in the
Established state or how long
since this peer was last in the
Established state. It is set to zero when
a new peer is configured or the router is
booted."::={ nsVrBgpPeerEntry 16}nsVrBgpPeerConnectRetryInterval OBJECT-TYPESYNTAXINTEGER(1..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Time interval in seconds for the
ConnectRetry timer. The suggested value
for this timer is 120 seconds."::={ nsVrBgpPeerEntry 17}nsVrBgpPeerHoldTime OBJECT-TYPESYNTAXINTEGER(0 | 3..65535)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Time interval in seconds for the Hold
Timer established with the peer. The
value of this object is calculated by this
BGP speaker by using the smaller of the
value in nsVrBgpPeerHoldTimeConfigured and the
Hold Time received in the OPEN message.
This value must be at lease three seconds
if it is not zero (0) in which case the
Hold Timer has not been established with
the peer, or, the value of
nsVrBgpPeerHoldTimeConfigured is zero (0)."::={ nsVrBgpPeerEntry 18}nsVrBgpPeerKeepAlive OBJECT-TYPESYNTAXINTEGER(0 | 1..21845)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Time interval in seconds for the KeepAlive
timer established with the peer. The value
of this object is calculated by this BGP
speaker such that, when compared with
nsVrBgpPeerHoldTime, it has the same
proportion as what
nsVrBgpPeerKeepAliveConfigured has when
compared with nsVrBgpPeerHoldTimeConfigured.
If the value of this object is zero (0),
it indicates that the KeepAlive timer has
not been established with the peer, or,
the value of nsVrBgpPeerKeepAliveConfigured is
zero (0)."::={ nsVrBgpPeerEntry 19}nsVrBgpPeerHoldTimeConfigured OBJECT-TYPESYNTAXINTEGER(0 | 3..65535)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Time interval in seconds for the Hold Time
configured for this BGP speaker with this
peer. This value is placed in an OPEN
message sent to this peer by this BGP
speaker, and is compared with the Hold
Time field in an OPEN message received
from the peer when determining the Hold
Time (nsVrBgpPeerHoldTime) with the peer.
This value must not be less than three
seconds if it is not zero (0) in which
case the Hold Time is NOT to be
established with the peer. The suggested
value for this timer is 90 seconds."::={ nsVrBgpPeerEntry 20}nsVrBgpPeerKeepAliveConfigured OBJECT-TYPESYNTAXINTEGER(0 | 1..21845)
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Time interval in seconds for the
KeepAlive timer configured for this BGP
speaker with this peer. The value of this
object will only determine the
KEEPALIVE messages' frequency relative to
the value specified in
nsVrBgpPeerHoldTimeConfigured; the actual
time interval for the KEEPALIVE messages
is indicated by nsVrBgpPeerKeepAlive. A
reasonable maximum value for this timer
would be configured to be one
third of that of
nsVrBgpPeerHoldTimeConfigured.
If the value of this object is zero (0),
no periodical KEEPALIVE messages are sent
to the peer after the BGP connection has
been established. The suggested value for
this timer is 30 seconds."::={ nsVrBgpPeerEntry 21}nsVrBgpPeerMinASOriginationInterval OBJECT-TYPESYNTAXINTEGER(1..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Time interval in seconds for the
MinASOriginationInterval timer.
The suggested value for this timer is 15
seconds."::={ nsVrBgpPeerEntry 22}nsVrBgpPeerMinRouteAdvertisementInterval OBJECT-TYPESYNTAXINTEGER(1..65535)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Time interval in seconds for the
MinRouteAdvertisementInterval timer.
The suggested value for this timer is 30
seconds."::={ nsVrBgpPeerEntry 23}nsVrBgpPeerInUpdateElapsedTime OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Elapsed time in seconds since the last BGP
UPDATE message was received from the peer.
Each time nsVrBgpPeerInUpdates is incremented,
the value of this object is set to zero
(0)."::={ nsVrBgpPeerEntry 24}nsVrBgpPeerVRID OBJECT-TYPE
SYNTAXINTEGER(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Virtual Router ID. VRID range for system created
VRs: [1-1024] and for user created VRs: [1025-2048]"::={ nsVrBgpPeerEntry 25}-- BGP-4 Received Path Attribute Table. This table-- contains, one entry per path to a network, path-- attributes received from all peers running BGP-4.nsVrBgp4PathAttrTable OBJECT-TYPESYNTAXSEQUENCEOF NsVrBgp4PathAttrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"The BGP-4 Received Path Attribute Table
contains information about paths to
destination networks received from all
BGP4 peers."::={ nsVrBgp 6}nsVrBgp4PathAttrEntry OBJECT-TYPESYNTAX NsVrBgp4PathAttrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about a path to a network."INDEX{ nsVrBgp4PathAttrVRID,
nsVrBgp4PathAttrIpAddrPrefix,
nsVrBgp4PathAttrIpAddrPrefixLen,
nsVrBgp4PathAttrPeer }::={ nsVrBgp4PathAttrTable 1}
NsVrBgp4PathAttrEntry ::=SEQUENCE{
nsVrBgp4PathAttrPeer
IpAddress,
nsVrBgp4PathAttrIpAddrPrefixLen
INTEGER,
nsVrBgp4PathAttrIpAddrPrefix
IpAddress,
nsVrBgp4PathAttrOrigin
INTEGER,
nsVrBgp4PathAttrASPathSegment
OCTETSTRING,
nsVrBgp4PathAttrNextHop
IpAddress,
nsVrBgp4PathAttrMultiExitDisc
INTEGER,
nsVrBgp4PathAttrLocalPref
INTEGER,
nsVrBgp4PathAttrAtomicAggregate
INTEGER,
nsVrBgp4PathAttrAggregatorAS
INTEGER,
nsVrBgp4PathAttrAggregatorAddr
IpAddress,
nsVrBgp4PathAttrCalcLocalPref
INTEGER,
nsVrBgp4PathAttrBest
INTEGER,
nsVrBgp4PathAttrUnknown
OCTETSTRING,
nsVrBgp4PathAttrVRID
INTEGER}nsVrBgp4PathAttrPeer OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The IP address of the peer where the path
information was learned."::={ nsVrBgp4PathAttrEntry 1}nsVrBgp4PathAttrIpAddrPrefixLen OBJECT-TYPESYNTAXINTEGER(0..32)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Length in bits of the IP address prefix
in the Network Layer Reachability
Information field."::={ nsVrBgp4PathAttrEntry 2}nsVrBgp4PathAttrIpAddrPrefix OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An IP address prefix in the Network Layer
Reachability Information field. This object
is an IP address containing the prefix with
length specified by
nsVrBgp4PathAttrIpAddrPrefixLen.
Any bits beyond the length specified by
nsVrBgp4PathAttrIpAddrPrefixLen are zeroed."::={ nsVrBgp4PathAttrEntry 3}
nsVrBgp4PathAttrOrigin OBJECT-TYPESYNTAXINTEGER{igp(1),-- networks are interioregp(2),-- networks learned-- via EGPincomplete(3)-- undetermined}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The ultimate origin of the path
information."::={ nsVrBgp4PathAttrEntry 4}nsVrBgp4PathAttrASPathSegment OBJECT-TYPESYNTAXOCTETSTRING(SIZE(2..255))
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The sequence of AS path segments. Each AS
path segment is represented by a triple
<type, length, value>.
The type is a 1-octet field which has two
possible values:
1 AS_SET: unordered set of ASs a
route in the UPDATE
message has traversed
2 AS_SEQUENCE: ordered set of ASs
a route in the UPDATE
message has traversed.
The length is a 1-octet field containing the
number of ASs in the value field.
The value field contains one or more AS
numbers, each AS is represented in the octet
string as a pair of octets according to the
following algorithm:
first-byte-of-pair = ASNumber / 256;
second-byte-of-pair = ASNumber & 255;"::={ nsVrBgp4PathAttrEntry 5}nsVrBgp4PathAttrNextHop OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The address of the border router that
should be used for the destination
network."::={ nsVrBgp4PathAttrEntry 6}nsVrBgp4PathAttrMultiExitDisc OBJECT-TYPESYNTAXINTEGER(-1..2147483647)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This metric is used to discriminate
between multiple exit points to an
adjacent autonomous system. A value of -1
indicates the absence of this attribute."::={ nsVrBgp4PathAttrEntry 7}nsVrBgp4PathAttrLocalPref OBJECT-TYPESYNTAXINTEGER(-1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The originating BGP4 speaker's degree of
preference for an advertised route. A
value of -1 indicates the absence of this
attribute."::={ nsVrBgp4PathAttrEntry 8}
nsVrBgp4PathAttrAtomicAggregate OBJECT-TYPESYNTAXINTEGER{lessSpecificRrouteNotSelected(1),lessSpecificRouteSelected(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Whether or not the local system has
selected a less specific route without
selecting a more specific route."::={ nsVrBgp4PathAttrEntry 9}nsVrBgp4PathAttrAggregatorAS OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-only
STATUScurrentDESCRIPTION"The AS number of the last BGP4 speaker that
performed route aggregation. A value of
zero (0) indicates the absence of this
attribute."::={ nsVrBgp4PathAttrEntry 10}nsVrBgp4PathAttrAggregatorAddr OBJECT-TYPESYNTAXIpAddressMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The IP address of the last BGP4 speaker
that performed route aggregation. A value
of 0.0.0.0 indicates the absence of this
attribute."::={ nsVrBgp4PathAttrEntry 11}nsVrBgp4PathAttrCalcLocalPref OBJECT-TYPE
SYNTAXINTEGER(-1..2147483647)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The degree of preference calculated by the
receiving BGP4 speaker for an advertised
route. A value of -1 indicates the
absence of this attribute."::={ nsVrBgp4PathAttrEntry 12}nsVrBgp4PathAttrBest OBJECT-TYPESYNTAXINTEGER{false(1),-- not chosen as best routetrue(2)-- chosen as best route}
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"An indication of whether or not this route
was chosen as the best BGP4 route."::={ nsVrBgp4PathAttrEntry 13}nsVrBgp4PathAttrUnknown OBJECT-TYPESYNTAXOCTETSTRING(SIZE(0..255))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"One or more path attributes not understood
by this BGP4 speaker. Size zero (0)
indicates the absence of such
attribute(s). Octets beyond the maximum
size, if any, are not recorded by this
object."
::={ nsVrBgp4PathAttrEntry 14}nsVrBgp4PathAttrVRID OBJECT-TYPESYNTAXINTEGER(0..65535)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Virtual Router ID. VRID range for system created
VRs: [1-1024] and for user created VRs: [1025-2048]"::={ nsVrBgp4PathAttrEntry 15}-- Traps.nsVrBgpTraps OBJECTIDENTIFIER::={ nsVrBgp 7}nsVrBgpEstablished NOTIFICATION-TYPEOBJECTS{ nsVrBgp4PathAttrVRID,
netscreenTrapType,
netscreenTrapDesc,
nsVrBgpPeerIdentifier,
nsVrBgpPeerLastError,
nsVrBgpPeerState }STATUScurrentDESCRIPTION"The BGP Established event is generated when
the BGP FSM enters the ESTABLISHED state."::={ nsVrBgpTraps 1}END